The 3D view isn’t available right now. Here is the top view.
The app was updated. Reloading the page…
Its files couldn’t be loaded. Reload the page; if that doesn’t help, check your connection.
Your browser can’t start WebGL right now. The 3D view comes back by itself once it can; if it doesn’t, restart the browser (Chrome switches WebGL off after a graphics crash) and check that hardware acceleration is on.
Your browser can’t start WebGL right now. Restarting the browser usually helps (Chrome switches WebGL off after a graphics crash); also check that hardware acceleration is turned on.
It stopped with an error. Try again; if it keeps happening, reload the page.
Details
The cutting plan appears once the preview is ready.
The cutting plan can’t be built right now. The 3D view still shows your design.
Cut Score No score lines Engrave Gluing guide
About this laser cut file
The turkey grins with a little beak and a wattle, its big fan of tail feathers spread behind it in a half circle, and it stands right on the band between two pumpkins and a tangle of maple leaves.
Below the band, oak leaves, acorns and one more pumpkin close the circle.
Hang it on the front door from November on to greet the guests for the feast, set it on the buffet beside the pie, or give it as a hostess gift with the family name on the band. It stays up all fall, so it works as an autumn sign long after the turkey is eaten.
How it works
-
Type the family name or the word for the band - The Millers, Thankful or Welcome all fit.
-
Pick the construction: One piece (Cut out or Engraved) or Layered, with the name glued on a frame across the band.
-
Pick the width under Size, from 3.54 to 23.62 in. The joints of the name, the hanging hole and the stand’s tabs keep their size; at the small end the feathers’ finest lines are cut a little bolder.
-
The band sets the name as large as it fits; pick a hanging hole for the door or a stand for the table.
-
Turn the sign in the 3D view, check the cutting plan and download the SVG.
What’s in the file
- Every piece on one sheet: the round sign, the name to glue on when layered, and the base plate with its slots when it stands.
- Cut lines, the name as an engraving when you engrave it, and the score lines and gluing guide when switched on.
- One SVG at full size, ready for your laser software.
- A template file of your settings, to load again for another family.
- SVG for every laser: the cut lines red, the score lines and the engraving blue, the gluing guide green, each on a layer of its own, true to size.
- PNG for raster engraving: the engraving alone - the score lines, the engraved areas and the gluing guide black on transparent at 600 dpi, as large as the sheet, so imported true to size it lies exactly on the SVG’s cut lines.
- PDF to print and proof: the same lines as vectors, true to size, every kind of line on a layer of its own - printed at 100 %, it shows the real size.
- AI for Illustrator: the same file as the PDF, which Illustrator opens as its own document, every kind of line on a layer of its own.
- DXF for CAD programs and RDWorks: the lines on the layers CUT, SCORE, ENGRAVE and GUIDE, in mm.
- STL to 3D print the design: the pieces as solids at their thickness - with several parts a ZIP with the whole piece and one STL per part.
- With Batch, several names at once: a ZIP with one file per name, or one sheet with all of them.
Questions
What happens to letters that reach out of the band?
They keep their full shape. The descender of a g, j, p or y, a swash or a tall capital lies on the artwork, welded to it, while the rails and the ring of the sign stay whole. Switch on Score overlaps to score the letter’s edge where it crosses the artwork.
One piece or Layered: which should I pick?
One piece is cut from a single sheet: Cut out sets the name into the band, its letters joined to the rails, Engraved engraves it on a frame across the band. Layered cuts the name as its own piece and glues it onto a frame across the band, in a second material.
Does the turkey’s tail stay in one piece?
Yes. Every feather touches the next and the ring at the top, and the lines along their middles stop short of their ends, so the whole fan stays one piece with the sign.
Can I write Thankful or Welcome instead of a name?
Yes. Any word or short phrase fits on the band: a family name, Thankful, Gather or Welcome. Longer words are set a little smaller so they still fill the band.
Can I make one for every name on a list?
Yes. Choose “Batch” above the first text and paste your list, one piece per line, up to 100. Every line becomes its own piece: download a ZIP with one file each, or one sheet with all of them.
More laser cut files
All laser cut files-
Pumpkin Patch Name Sign
A round Halloween sign: a scarecrow, a full moon and grinning pumpkins over the name.
-
Halloween Name Sign
A haunted house, bats and grinning pumpkins over the name on a rectangular sign.
-
Bird Wreath Name Sign
A wreath with a bird and your name on a hanging plate.
-
Kitchen Name Sign
Kitchen utensils with a name between the lines.