Menu

3D preview of the Leaf Scroll photo stand: one smooth curve and a foot that curls into scrolls at both ends

Your file SVG · For every laser

Choose your format

Your settings

Size
120 mm tall · 115 mm deep
Sheet
3 mm · kerf 0.15 mm
Cutting plan
–

Free for personal use For your own projects and gifts, not for sale. Selling needs the commercial license. Sell commercially now

About this laser cut file

It rises in one smooth curve from a foot that curls into scrolls at both ends, the front one unfurling like a leaf.

It suits a photo, a card or a small plate.

The two halves slot together crosswise and hold each other without glue. The slots are drawn for your sheet: enter its thickness and how much your laser burns away, and the halves push together snugly, also when you stretch the stand deeper or slimmer.

How it works

  1. Set the height under Size. With Keep proportions on, the depth follows; off, set the depth on its own, from 0.7 to 1.4 times as deep as the design is drawn.

  2. Measure your sheet and enter its thickness and your kerf under Sheet.

  3. Look at the assembled stand in 3D: Front shows one half straight on, Apart lifts one half off the other. Check the cutting plan, then download the SVG.

What’s in the file

  • Cut lines for both halves, nested on one sheet at true size.
  • Slots drawn one kerf narrower than your sheet, so after cutting they are exactly as wide as the sheet is thick and the halves slot together firmly.
  • The slots keep their true width at every height and depth.
  • Optional: both halves as a 3D model (STL), for a 3D viewer or a 3D printer.
  • SVG for every laser: the cut lines red, the score lines and the engraving blue, the gluing guide green, each on a layer of its own, true to size.

Questions

Where are the scrolls on the leaf scroll stand?

At both ends of the foot: the front curls up like an unfurling leaf, the back rolls into a smaller scroll, and the post rises from between them in one smooth curve.

Why do I need to enter the sheet thickness?

The two halves hold each other only through their slots. A slot that is too wide lets the stand wobble, one that is too narrow will not go together. Measure the sheet you will cut and enter it, and the slots are made for it.

What is the kerf and which value should I use?

The kerf is the width the laser beam burns away. Every slot is drawn one kerf narrower than the sheet, so after cutting it is exactly as wide as the sheet. 0.006 in is a good start for most lasers; a larger value makes the joint tighter, a smaller one looser. Cut one stand first to check.

Can I scale the file in my laser software?

Better not: scaling the file scales the slots too, and they no longer fit the sheet. Set the height and the depth here instead, from 1.65 to 14.17 in tall, and the slots stay matched to your sheet at every size.

Does it work with any sheet?

The slots fit any sheet from 0.039 to 0.47 in, but a thick sheet in a small stand can push the halves into each other where ornament sits close to the joint. The notes then say so and what to change.

How do I put the stand together?

Take the half whose slot opens at the top and slide the other half down into it, crosswise, until both stand flat on the table. The slots hold them; no glue is needed. Pull the halves apart again to store the stand flat.

What is the STL download for?

It is the stand as a 3D model: both halves laid flat, as thick as the sheet, with the slots exactly as wide as the sheet. Open it in a 3D viewer to check the stand, or print it on a 3D printer. For the laser, use the SVG.

Your file is ready

Sign up in 5 seconds and download it, with 5 laser cut files every day after.

At least 6 characters. You sign in with your e-mail address and this password.

Already have an account?

By creating an account you agree to our Terms and our Privacy policy.