The 3D view isn’t available right now. Here is the top view.
The app was updated. Reloading the page…
Its files couldn’t be loaded. Reload the page; if that doesn’t help, check your connection.
Your browser can’t start WebGL right now. The 3D view comes back by itself once it can; if it doesn’t, restart the browser (Chrome switches WebGL off after a graphics crash) and check that hardware acceleration is on.
Your browser can’t start WebGL right now. Restarting the browser usually helps (Chrome switches WebGL off after a graphics crash); also check that hardware acceleration is turned on.
It stopped with an error. Try again; if it keeps happening, reload the page.
Details
The cutting plan appears once the preview is ready.
The cutting plan can’t be built right now. The 3D view still shows your design.
Cut Score No score lines Engrave Gluing guide
About this laser cut file
Two tall ears stand up over a ribbon, each with a pattern of leaves inside.
Below the ribbon a long, straight stake goes deep into the soil, so the ears seem to be peeking out of the flowers.
Write a name for each child’s little pot or a greeting such as Hoppy Easter, and it doubles as a place card at the Easter table. Teachers and neighbors tend to love these, and they cost next to nothing to make in a batch.
Glued up in color, the ears and their leaves look fresh among green leaves. Engraved in one piece on thin plywood, every leaf stays a clean line, and it is ready the moment the laser stops.
How it works
-
Enter a greeting or a name for the ribbon, up to 16 characters.
-
Pick Layered for colored ears, or One piece for every line engraved on a single board.
-
Set the width from 3.54 to 9.84 in; a 5.12 in stake suits a medium flower pot.
-
Push the stake down into the soil, close to the pot’s rim so it stays upright.
What’s in the file
- Layered: the ribbon and the stake on a dark back plate, the two ears, their leaves, the ribbon’s tails and the words as parts of their own.
- One piece: a single thin board with every line engraved, the name on the ribbon.
- Gluing guide (optional, layered): where the ears and the leaves belong.
- SVG for every laser: the cut lines red, the score lines and the engraving blue, the gluing guide green, each on a layer of its own, true to size.
- PNG for raster engraving: the engraving alone - the score lines, the engraved areas and the gluing guide black on transparent at 600 dpi, as large as the sheet, so imported true to size it lies exactly on the SVG’s cut lines.
- PDF to print and proof: the same lines as vectors, true to size, every kind of line on a layer of its own - printed at 100 %, it shows the real size.
- AI for Illustrator: the same file as the PDF, which Illustrator opens as its own document, every kind of line on a layer of its own.
- DXF for CAD programs and RDWorks: the lines on the layers CUT, SCORE, ENGRAVE and GUIDE, in mm.
- STL to 3D print the design: the pieces as solids at their thickness - with several parts a ZIP with the whole piece and one STL per part.
- With Batch, several toppers at once: a ZIP with one file per topper, or one sheet with all of them.
Questions
Will it survive in wet soil?
For a few weeks, yes, especially with a coat of clear varnish on the lower half of the stake. For the garden itself, use a waterproof plywood or acrylic.
How deep should it go?
About a third of the stake is plenty. It should stand next to the plants rather than through their roots, and a pot with firm soil holds it best.
Does the stake break easily?
It runs straight down from the ribbon and, in the Layered version, is doubled by the back plate, so it is quite stiff. In a single thin board, keep it to pots with loose soil.
Can I put it in a gift box instead?
It also works as a tall cake topper or a pick in an Easter bread. Wrap the lower part in a little foil if it touches food.
Can I make one for every name on a list?
Yes. Choose “Batch” above the first text and paste your list, one piece per line, up to 100. Every line becomes its own piece: download a ZIP with one file each, or one sheet with all of them.