The 3D view isn’t available right now. Here is the top view.
The app was updated. Reloading the page…
Its files couldn’t be loaded. Reload the page; if that doesn’t help, check your connection.
Your browser can’t start WebGL right now. The 3D view comes back by itself once it can; if it doesn’t, restart the browser (Chrome switches WebGL off after a graphics crash) and check that hardware acceleration is on.
Your browser can’t start WebGL right now. Restarting the browser usually helps (Chrome switches WebGL off after a graphics crash); also check that hardware acceleration is turned on.
It stopped with an error. Try again; if it keeps happening, reload the page.
Details
The cutting plan appears once the preview is ready.
The cutting plan can’t be built right now. The 3D view still shows your design.
Cut Score No score lines Engrave Gluing guide
About this laser cut file
A bone-shaped tag sits inside the top of the frame and carries the dog’s name; below it, the round back plate leaves plenty of room for an engraved photo.
Two plates are glued on top of each other: the back plate and the front frame with its bone. Layered, the name is glued onto the bone as raised letters; in one piece the frame is cut alone, the name cut out of the bone or engraved into it. Hang it on the tree by its loop or stand it in a flat base.
How it works
-
Type the dog’s name and pick a font.
-
Pick the construction: Layered, with the name glued on, or One piece, with the name cut out or engraved.
-
Set the width under Size, from 1.57 to 12.99 in. The loop hole and the stand’s tabs and slots keep their size.
-
The name fits itself into its place. Layered, the open area of the back plate is where the photo goes.
-
Download the SVG, place your dog’s photo on the back plate in your laser software, and cut the plates.
What’s in the file
- Layered: cut lines for the back plate and the front frame, side by side on one sheet, plus the name to glue on.
- One piece: the frame with the name cut out, its insides on small bridges, or engraved, filled or as outlines.
- On the stand: the plates cut straight at the bottom, tabs into a base plate with matching slots.
- At the size you set: the loop hole, the tabs and the slots at their true size, and a cut-out name too small to cut is engraved for you.
- The photo is not part of the file: you place it on the back plate in your laser software.
- Batch: a ZIP with one file per name, or one sheet with both plates of every name.
- SVG for every laser: the cut lines red, the score lines and the engraving blue, the gluing guide green, each on a layer of its own, true to size.
- PNG for raster engraving: the engraving alone - the score lines, the engraved areas and the gluing guide black on transparent at 600 dpi, as large as the sheet, so imported true to size it lies exactly on the SVG’s cut lines.
- PDF to print and proof: the same lines as vectors, true to size, every kind of line on a layer of its own - printed at 100 %, it shows the real size.
- AI for Illustrator: the same file as the PDF, which Illustrator opens as its own document, every kind of line on a layer of its own.
- DXF for CAD programs and RDWorks: the lines on the layers CUT, SCORE, ENGRAVE and GUIDE, in mm.
- STL to 3D print the design: the pieces as solids at their thickness - with several parts a ZIP with the whole piece and one STL per part.
- With Batch, several names at once: a ZIP with one file per name, or one sheet with all of them.
Questions
How big can the name be on the bone tag?
As large as fits the bone’s middle, with a little margin to its edges, centered on the ornament. A short name fills it; a long one is set smaller, and a tighter letter spacing gives it more size.
Where does the dog’s photo go?
Layered, on the back plate, in the area the front frame leaves open. The photo is not part of the file: place your picture there in your laser software and engrave it before you glue the frame on.
Layered or one piece?
Layered cuts the back plate, the frame and the name: the frame is glued onto the back plate and the name on top, so it stands out in a second tone. One piece cuts the frame alone, with the name cut out, the insides of letters such as a, e and o held by small bridges, or engraved, filled or as outlines.
How are the two plates assembled?
Cut both plates, engrave the photo on the back plate, then glue the front frame on top so that the two outlines line up. Under Mount, choose Hole to hang it on a ribbon, Stand to set it in a flat base plate (its tabs fit slots cut to your sheet thickness), or None.
Can I make one for every name on a list?
Yes. Choose “Batch” above the first text and paste your list, one piece per line, up to 100. Every line becomes its own piece: download a ZIP with one file each, or one sheet with all of them.